How to use the serger sewing device to make a simple serger

The serger is one of the most important sewing machines of the 20th century.

It was invented in Germany by the Swiss engineer Erich Serger and patented in 1902.

This is a basic, unmodified serger.

But it has been greatly improved over the years.

Serger sewing machines are quite useful for making everything from sewing clothing to buttons and buttons with a simple sewing machine, including tasseled buttons.

These simple sewing machines can be easily made to fit any occasion, whether it is a wedding or birthday party.

This simple serging machine was popularized in the early 20th Century.

It is a simple machine made of a simple steel frame, a metal needle, and a simple wooden handle.

It uses only a single serger and can easily be made to accommodate all kinds of things.

If you need a sewing machine that is more complicated than this, you can buy one of these basic serger machines from a hardware store, a machine shop, or online.

This serger machine is one simple, simple machine that makes simple sewing tasks easy.

The serge is the only sewing machine you will need to make all sorts of things that are not made to use a serger: buttons, buttons with tassels, buttons that are embroidered, and other things that you can attach to clothing or accessories.

You can make a serging, or any serger, from the following parts: a serged steel plate with a loop that fits into the bottom of the serged plate, a small flat-topped iron needle, a wood handle, and thread.

This piece of iron is the part that will be used to pull the needle up through the metal plate.

If you are making a serge with a wooden handle, it should have a small handle with a screw on the end that will hold the serge into the wooden handle in the proper position.

This handle is called a ring.

I have already described how to make an inexpensive serging with a single iron needle.

But you will want to make the same basic serging that I am using in this post, with two metal needles.

I will call it a three-needle serge.

You can get two different serging designs: one that is made with a ring and one that does not.

For this example, I will make the first version of the three-finger serge, but you can also make the two-finger version.

First, I need to buy two metal handles, which you can get at hardware stores or from any hardware store.

I use the handle that I purchased from the hardware store for this example.

The metal handle is about three feet long.

This metal handle will be the part of the metal that will carry the iron needle through the steel plate.

You will need the metal handle to attach the iron to the plate.

If there is not enough room for the iron on the steel, the iron will fall through the hole that I made in the steel.

The iron needle can be attached to the metal end of the steel by a small piece of metal wire that I bought at a hardware or craft store.

The wire is about one inch long.

You’ll also need the wooden needle to attach it to the steel and to hold it in place.

I buy a metal wire for $3.50 from the local hardware store because I do not need to use it.

It can be purchased for $1.50 at a local hardware or crafts store.

This wire has a metal tip and it has a small hole in the end to fit the iron.

You want to attach your iron needle to the wire.

I attach my iron needle with the metal tip.

I am not going to go into too much detail here, but I am going to tell you how to attach iron to wire.

First, I am attaching the iron tip to the wooden end of my iron wire.

The steel plate is made of metal that is just a few millimeters thick.

So the tip of the iron wire is attached to one of two metal plates that are two inches in diameter.

The second plate is the steel rod that goes into the tip.

This steel rod is held in place by a metal bar.

This bar is also held in a groove in the wooden plate.

This plate has a hole in it so the iron can slide into the hole.

I don’t have to tell anyone about this.

You need to put a small loop in the metal rod to hold the iron in place on the metal bar so it doesn’t fall through.

This loop is a little bit longer than the length of the wire that is attached.

If the loop is too long, the steel will fall out of the hole and fall into the steel bar that is holding it in the middle.

The loop of the wood handle is attached so the loop can be turned.

You put the loop on the wood end of your metal needle.

The wooden end has